Cone-crusher at 02:26, 18 January 2008

2008-01-18T02:26:11Z

@@ Line 1: / Line 1: @@
-A [http://www.stone-crusher.org/cone-crusher.html cone crusher] breaks rock by squeezing the rock between an eccentrically gyrating spindle, which is covered by a wear resistant mantle,
+Beneficiation plant commonly used crusher and grinding mills
- and the enclosing concave hopper, covered by a manganese concave or a bowl liner. As rock enters the top of the cone crusher,
+Filed under: grinding mill, jaw crusher, crusher — admin @ 7:19 pm Edit This
-it becomes wedged and squeezed between the mantle and the bowl liner or concave. Large pieces of ore are broken once, and then fall
+According to the fragmentation of the role of methods can be broken roughly divided into two categories:
-The [http://www.made-in-china.com/showroom/shshibang/product-detailJqKESPIvJQVt/China-Cone-Crusher.html cone crusher] is characterized by great crushing force, high efficiency, great capacity, low cost, convenient adjustment
+ (1) Crusher
-Working principle:
+(2) grinding machine.
-If the foreign materials are stuck at the discharge outlet, use cavity-cleaning system to further expand the outlet,
+Breakers general handling large block of materials, products coarse granularity usually greater than 8 mm. Its structure is characterized by broken pieces of a certain gap between not contact each other. Breakers can be divided into rough broken machine, and a chronology of broken machines. Generally grinding machine materials handled by the smaller, product size is fine, up to 0.074 mm, and even more detailed. Its structure is characterized by broken parts (or medium) mutual contacts, the media is used by the steel balls, steel bars, such as gravel or Ore. But some machinery at the same time is both crushing and grinding role, such as self-grinder. ∮ 5.5 × 1.8 m ore processing mill since the size limit up to 350-400 mm, product fine of up to -200 mesh accounted for 40 percent.
-  so as to discharge the foreign materials from the crushing cavity. Under the action of spring, the discharge outlet
-  recovers by itself, and the equipment returns to normal
+According broken, the structural characteristics of machinery (action principle) to the division, in general, divided into six categories.

Cone-crusher at 11:24, 7 January 2008

2008-01-07T11:24:38Z

New page

A [http://www.stone-crusher.org/cone-crusher.html cone crusher] breaks rock by squeezing the rock between an eccentrically gyrating spindle, which is covered by a wear resistant mantle,
and the enclosing concave hopper, covered by a manganese concave or a bowl liner. As rock enters the top of the cone crusher,
it becomes wedged and squeezed between the mantle and the bowl liner or concave. Large pieces of ore are broken once, and then fall
to a lower position (because they are now smaller) where they are broken again. This process continues until the pieces are small
enough to fall through the narrow opening at the bottom of the crusher.

The [http://www.made-in-china.com/showroom/shshibang/product-detailJqKESPIvJQVt/China-Cone-Crusher.html cone crusher] is characterized by great crushing force, high efficiency, great capacity, low cost, convenient adjustment
and economical application, etc. Due to reasonable selection of components and design of structure, service life of
the equipment is long. The crushed products are with even grain to decrease the cyclic load. Large and medium-sized
crushers adopt hydraulic cavity cleaning system so as to reduce the down-time. There are a lot of types of
crushing cavities for each type of crusher. Customers can select according to their different requirements.

Working principle:
The motor is forced by eccentric sleeve through belt pulley or coupling, driving shaft and the cone to
oscillate and rotate around a certain axis, so as to make the crushing wall close to and far away from
surface of the liner plate fixed on the adjusting sleeve. The ore is crushed by continuous impact,
extrusion and flexural action in the crushing cavity. When non-broken foreign materials pass through
the crushing cavity or the cone crusher is overloaded for some reasons, the spring safe system begins
to protect the equipment by expanding the discharging outlet to discharge the foreign materials from the crushing cavity.

If the foreign materials are stuck at the discharge outlet, use cavity-cleaning system to further expand the outlet,
so as to discharge the foreign materials from the crushing cavity. Under the action of spring, the discharge outlet
recovers by itself, and the equipment returns to normal

Cone-crusher - Revision history

Cone-crusher at 02:26, 18 January 2008

Cone-crusher at 11:24, 7 January 2008